The Haul Manual

Fit checks

Measure a garment you own before you buy another

Four flat measurements, one soft tape, and a tolerance band turn a seller's size chart into something you can use. Here is the order to take them in, and where the numbers mislead.

The fastest way to buy the wrong size is to trust a letter. The second fastest is to measure your body and compare it to a garment chart. What you actually need is four flat numbers from a garment that already fits, taken the same way a seller takes theirs. The numbers decide fit; the letter on the label does not.

This page covers the four measurements, how to take them without stretching the fabric, the tolerance you should assume, and how to read a chart that may be describing a person rather than a shirt.

Four numbers that decide fit

Pit to pit, body length, shoulder width and sleeve length explain most fit failures. Pit to pit is the flat chest width from one underarm seam to the other. Body length runs from the base of the collar, or the high point of the shoulder on a hooded item, down to the hem. Shoulder width spans seam to seam across the back. Sleeve length runs from that shoulder seam to the cuff edge.

Chest circumference is roughly double the pit-to-pit figure, but only roughly. Flattening a curved chest costs a centimeter or two, so the two numbers never convert perfectly. Use pit to pit when the chart is flat, and circumference when the chart is written that way.

For trousers, add waist, inseam and front rise. Shoulder width is the number buyers skip, and it decides whether the seam sits on your shoulder or hangs past it. For a first order, four numbers on a top are enough to catch most mistakes.

Lay it flat, then measure

Button or zip the garment, lay it on a hard table, and smooth it without pulling. Measure with a soft tape held flat, not tight. Read to the nearest half centimeter and write the number down twice if it sits near a boundary.

Pit to pit: seam to seam, straight across, tape parallel to the hem. Body length: from the collar base at the back, or the high shoulder point if there is a hood, straight down to the hem edge. Shoulder: from the sleeve seam on one side to the other across the back. Sleeve: from that shoulder seam to the cuff edge, following the outer line.

Repeat each measurement once. If the two readings differ by more than half a centimeter, the garment was not flat or the tape was twisted.

MeasurementStart pointEnd point
Pit to pitLeft underarm seamRight underarm seam
Body lengthCollar base at the backHem edge
ShoulderLeft sleeve seamRight sleeve seam
SleeveShoulder seamCuff edge, outer line

The tolerance you should assume

Sewing is not machining. A tolerance of 1 to 2 cm between the chart and the garment is normal across most mass-market production. One centimeter on a chest is invisible; two centimeters turns a fitted garment into a relaxed one.

Your own measurement also carries error, usually half a centimeter to a centimeter on soft fabric. Two tolerances stack: your tape plus their sewing. Treat a 2 cm gap as noise, a 3 cm gap as a question, and a 4 cm gap or more as the wrong item.

Shoulder and sleeve tolerances are tighter in practice, because a 2 cm shift changes where the seam sits on your arm. Chest and length are more forgiving.

Comparing your numbers to a chart

First, find out which kind of chart the seller published. Garment measurements describe the item flat. Body measurements describe the person. A chart headed chest with a number like 118 for a size L is usually a body circumference in centimeters, and if you compare it to your flat pit to pit doubled, you will order a tent.

Match like with like. If the chart is flat, compare your flat number plus the tolerance. If the chart is circumference, multiply your pit to pit by two, add 2 to 4 cm for the curve, then compare. If the chart mixes both, trust only the rows you can identify with confidence.

Write your four numbers on a note you keep. Re-measuring the same hoodie before every order is how people end up with three sizes of the same mistake.

Where the chart lies

Charts are written by sellers, sometimes from a sample, sometimes from a template copied between listings. The same chart can appear on five listings with five different fabrics. A size L in a heavy fleece and a size L in a thin cotton tee are not the same garment even when the numbers match.

Fabric changes fit after the first wash. A cotton jersey can shrink 2 to 5 percent in length, and a loose knit can relax across the chest. If the chart sits exactly at your limit, pick the larger size or a different fabric.

Photos of a tape measure lying on the garment are the closest thing to evidence. If a listing includes them, compare those numbers, not the table.

A five-minute routine before every order

Pull the garment you wear most from the drawer. Measure the four numbers. Open the listing, identify the chart type, and compare. Note the difference for each number. If two or more numbers are more than 2 cm off in the direction that matters, change size or skip the item.

Keep a simple table on your phone: garment name, four numbers, date measured, and how the purchased item actually fitted. After three orders you will know your real numbers better than any chart, and the routine drops to two minutes. Save the numbers in a note you can find from the checkout page.

What this guide assumes

That you are buying a normal consumer item from a Chinese marketplace through an agent, that you will declare it accurately, and that you understand the seller, not the agent, controls the item. Where a number varies by route, season or account, the range is given and the reason is named.

Reviewed 2026-11-18. Written from operator documentation, published rate cards and reader reports. No operator paid for inclusion or for a verdict. Editorial standards.

Questions that come up

Should I measure my body or a garment?

Both, for different reasons. Body numbers tell you the target, and garment numbers tell you what the item actually is. For comparing to a seller chart, the garment measurement is the one that matches.

What if my garment has stretch?

Measure it relaxed, then again gently stretched, and record both. A chart number that matches the relaxed figure will fit like the garment does on a normal day; one that matches the stretched figure will fit tight.

How much difference is acceptable?

Up to 2 cm is normal noise between a chart and a sewn garment. A 3 cm gap deserves a question to the seller, and 4 cm or more usually means a different size cut or a label error.

Partner catalogue

Ready to put the checklist to work?

Kakox is the catalogue we point readers to: curated finds from Taobao, Weidian and 1688, with warehouse photos before anything ships. Use the guides here to decide what to buy, then check the listing, the measurements and the QC photos before you commit.

Browse the curated catalogue